# Sizing the Gsike 12.8V 100Ah Battery: Watt-Hours, Depth of Discharge and Runtime for Spanish Off-Grid Plans

**By SIKE G** · 2026-11-21

Battery SizingRuntimeUsable EnergyOff-Grid Planning

# Sizing the Gsike 12.8V 100Ah Battery: Watt-Hours, Depth of Discharge and Runtime for Spanish Off-Grid Plans

Real load figures, rather than the amp-hour label, are the starting point when an off-grid store is sized, and this guide works through watt-hours, depth of discharge, inverter losses and runtime for the Gsike 12.8V 100Ah block in small Spanish system designs.

## Start from daily energy demand, not the amp-hour label

A dependable off-grid plan begins from the energy your loads actually consume over an ordinary day, expressed in watt-hours, rather than from the amp-hour rating printed on the battery. The Gsike 12.8V 100Ah block holds 1280Wh at the bus level, yet the share you may safely draw before refill depends on three adjustments: the depth of discharge you choose, the efficiency of the inverter converting DC to 230V AC, and the startup inrush of motors and compressors; when any of these steps is skipped, runtime estimates tend to turn optimistic and fall short in real use.

For a Spanish small-system design — a campervan leisure circuit, a boat battery, a garden shed with a modest panel array, or an evening home reserve — most daily loads sit at a low to moderate level: LED lighting, phone and laptop charging, a portable fridge, a small pump, a router or a fan. Writing down each appliance's wattage and its running hours produces a daily Wh figure that shows whether one 1280Wh block covers the plan or a larger bank is required, while high-draw devices such as electric heaters, induction hobs or large air-conditioning units should be treated as a separate system-sizing exercise.

The load list should be built around a representative day rather than a best-case one: a summer campervan may run lights, charging and a fridge over a weekend, whereas a winter cabin evening can add a light heating load that shifts the total completely. Note which loads run directly on DC and which must pass through the inverter, since inverter losses apply only on the AC side, and keep a column for startup current on motor-driven appliances, because inrush influences component selection even when its average Wh contribution is small.

![Notebook with load calculations beside the Gsike battery and a solar panel](https://cdn.shopify.com/s/files/1/0729/3042/7041/files/en-es-gsike-lifepo4-battery-12v100-p-31-bBek7Q2ba.jpg)

## Depth of discharge and usable energy

This block's cycle rating stands at 6000 cycles measured at 80% depth of discharge, with roughly 5000+ cycles when the full 100% DoD is reached. In practice an 80% usable band keeps cells away from their deepest discharges and supports the long design life, while the 10V cut-off exists as a protection limit rather than a routine working point; working from 1280Wh, an 80% DoD planning figure leaves about 1024Wh of usable DC energy before refill, though the exact share chosen will depend on how often solar, shore power or another source can restore the store.

| Planning step | Calculation basis | Note for this pack |
| --- | --- | --- |
| Stored DC energy | 12.8V × 100Ah = 1280Wh | Bus-level figure before any losses |
| Depth of discharge | Plan around 80% DoD for long cycle life | 10V cutoff is protection, not a daily target |
| Inverter efficiency | Apply 90–95% conversion derating | AC runtime is lower than the DC Wh figure |
| Startup inrush | Allow for one-second 400A pulse | Only a brief inrush; steady limit stays 100A |
| Daily recharge | Match refill source to daytime solar or shore input | MPPT or charger must use the 14.4V LFP profile |

Depth of discharge behaves differently for LFP than for traditional lead acid: many lead-acid banks are kept inside a 50% DoD band to preserve life, which means a nameplate capacity comparison can mislead, because the LFP block can safely draw on a deeper share of its energy than a comparable lead-acid block. Options should therefore be compared on usable Wh after your DoD choice, not on the raw Ah number alone, and it is worth recalling that repeated shallow cycles are gentler than repeated deep ones, so a slightly oversized store that stays above the 80% band tends to outlast one run flat every day.

![Solar panels on a roof feeding charge into the storage battery](https://cdn.shopify.com/s/files/1/0729/3042/7041/files/en-es-gsike-lifepo4-battery-12v100-p-32-EbVbBy4M7.jpg)

## Runtime worked through sample leisure days

A moderate campervan day serves as an illustration: LED lights for several evening hours, phone and tablet charging, a portable fridge cycling through the day, and occasional laptop use. Adding wattage and hours gives a daily Wh total, and after the chosen DoD band and the 90–95% inverter derating, what remains is the AC energy the block can support before a refill; if the fridge compressor draws a higher startup current, the block's 400A one-second pulse covers that brief instant, although the fridge's average running draw counts toward the steady 100A, 1280W DC ceiling.

A second sample is a day on the water: a trolling motor run in intervals across the day, together with lights and USB charging for accessories, where the average motor draw — rather than the peak throttle current — determines how long the 1280Wh lasts, with runtime swinging heavily on speed, wind and water conditions. A third sample is a cabin or home evening reserve: essential lights, a router and a few small appliances for several hours after sunset, drawing on what the array charged during the day, and in every case the steady combination of running loads has to stay below the continuous DC ceiling, while the usable Wh figure decides how long the reserve lasts.

A useful sanity check compares the planned daily draw against the block's usable band across several days rather than a single one, because if the array cannot refill the store fully on each sunny day, effective capacity shrinks further and the plan must either reduce loads, add panel area, or move to a second matched unit. Keeping a one- or two-day reserve inside the calculation also covers a stretch of cloudy weather without pushing the cells to the cut-off, and leaves headroom for an appliance that draws more than its label suggests on a warm day.

## Matching the recharge source to daily demand

A correctly sized store is paired with a refill source able to restore the day's draw before the next cycle. In a solar setup the MPPT controller has to use the 14.4V ±0.2V LFP profile, and the array should be planned against the sunlight available locally in the seasons when the system actually runs; because this battery's spec sheet records no maximum solar-panel wattage, that upper limit belongs to the controller's own rating, so array and controller current should be checked against your daily demand and the seller's guidance rather than assumed from the battery alone.

Where solar alone cannot cover the draw — for instance a winter cabin with short days, or a van during a cloudy stretch of travel — a shore or mains LiFePO4 charger, or an alternator-derived DC-DC charging path, acts as the backup refill. Everyday refills are recommended at 20A (0.2C), and although the BMS permits up to 100A continuous charge, the refill path should be matched to what the system realistically needs; when the daily draw consistently exceeds what one block and its refill source can restore, the plan points to a larger bank rather than deeper discharge on a single unit.

![Two storage batteries prepared for parallel expansion on a mounting board](https://cdn.shopify.com/s/files/1/0729/3042/7041/files/en-es-gsike-lifepo4-battery-12v100-p-33-Hu6YE2KUS.jpg)

## When one pack is not enough: expansion planning

When daily demand rises above the usable energy of one unit, the documented expansion path reaches 4P4S — 16 units forming a 20.48kWh bank, with 4S reaching 51.2V and 4P reaching 400Ah. Units joined that way should be identical and matched within roughly one month of production and charge history, since mixing new and worn cells, or units of different ages, unbalances the bank and shortens its life; for plans that stay small, a single 1280Wh block plus the right inverter and charger is the simpler starting point, with room to add units later if demand grows.

Expansion alters the system's voltage and current arithmetic: series wiring raises the bus voltage, parallel wiring raises capacity, and the inverter, charger and cables must be re-matched to the resulting bank. If a multi-unit bank is planned from the outset, the whole system should be sized around the final configuration rather than heavier cable or fuses being added later, and production dates and charge histories should be recorded so any future additions match the existing units as closely as possible.

Seasonal use in Spain also shapes the refill side: bright summer months give the array more hours to refill, while shorter winter days and weaker sun reduce what the panels return, so a system used through the cooler months should be planned around the weakest realistic refill period rather than the best one. If solar alone cannot restore the daily draw in that period, a shore or mains charger, or an engine-derived charging path on a vehicle, acts as backup refill, so the block is not repeatedly left partially charged.

## Building a realistic load table

The most useful sizing document is a simple load table built from your actual appliances rather than generic estimates. For each device, record its rated wattage or current, whether it runs on DC or through the inverter, the hours it typically runs in a day, and any note about startup current for motors or compressors; many appliance labels print watts or amps at the operating voltage, where only current appears it should be multiplied by the bus or appliance voltage to arrive at wattage, and any VA figure from an inverter-driven device should be treated as close to watts for planning purposes.

DC loads should be separated from AC loads before totalling, because inverter efficiency applies only on the AC side. A 12V LED strip or USB socket draws directly from the bus, whereas a laptop charger, a small TV or a kitchen appliance passes through the inverter and incurs the 90–95% conversion loss; adding the two groups together without that distinction tends to overstate what the battery must supply, while forgetting the inverter loss understates the DC energy the AC loads consume.

Daily watt-hours are the running wattage multiplied by the hours of use and summed across all loads. It is also worth marking which devices run at the same time, because the simultaneous steady total sets the current-ceiling check while the daily Wh total sets the capacity check; a fridge, for example, may cycle on and off across the whole day and contribute a moderate daily Wh even though it is never the only load, whereas a short high-power use adds little daily Wh but can matter for the continuous current limit.

| Load group | Connection | What to record | Sizing check |
| --- | --- | --- | --- |
| LED lighting, USB sockets | DC bus | Wattage and daily hours | Counts toward daily Wh directly |
| Portable compressor fridge | DC or inverter | Average draw, startup current, run time | Startup within pulse; average within 100A |
| Laptop, small TV, electronics | Through inverter | Wattage and daily hours | Apply 90–95% inverter derating |
| Motor or pump loads | DC or inverter | Running and startup current | Steady under 100A; inrush within 1s pulse |

Once the table is complete, compare the daily Wh against the usable energy of one 1280Wh block after your chosen DoD band and inverter derating, and compare the simultaneous steady current against the 100A continuous ceiling. If either figure leaves little or no headroom, the plan points to a larger bank; if both sit comfortably below the limits with room for variation, the single block is a reasonable starting size.

Reading the appliance label correctly avoids two common slip-ups: some devices print input current rather than wattage, so current should be multiplied by the operating voltage to obtain watts, while others list a maximum draw that appears only briefly, which should be separated from the average running draw. DC and AC figures should be totalled on their own sides of the inverter, since applying the 90–95% efficiency loss to a DC direct load overstates the battery's burden, whereas forgetting it on an AC load understates it.

## Seasonal adjustments and headroom in the sizing plan

Both loads and refill shift with the seasons, so a sizing plan built for a mild summer weekend may not hold through a colder or darker period. In Spain, summer use often centres on fridges, lighting and device charging in vans and boats, while winter cabins or low-sun evenings can add extra lighting and, in some cases, a modest heating-related load that changes the daily Wh total; solar refill likewise varies with daylight hours and weather, so the array should be planned around the season when the system is used most, not the brightest month of the year.

Headroom on depth of discharge protects cycle life: planning to stay around the 80% DoD band rather than draining to the 10V cut-off each evening keeps cells away from their deepest state and supports the 6000-cycle rating and ten-year design life. A store that finishes each day with some spare Wh also absorbs an unexpectedly long appliance run, a cloudy refill day or a higher-than-estimated load without hitting the protection cut-off, and sizing slightly above the calculated minimum usually costs less over time than running an undersized block flat every cycle.

If the first season of real use shows demand outgrowing the single block, the documented expansion path adds matched identical units up to a 4P4S, 20.48kWh bank. The units should be close in production date and charge history, and the inverter, charger, cables and fuses should be re-matched to the resulting bank; starting with one block does not lock you into a fixed capacity, but the mounting space, cable routing and fuse positions should leave room for the planned growth when the install is first laid out.

Once a season has passed, go back over the load table using what you have actually measured — how often the fridge cycles, how many hours charging really took, and whatever appliances have since been added or removed. Measured state-of-charge behaviour should be compared against the original estimate, and the decision then made whether to adjust load habits, enlarge the bank or change the refill source; sizing is rarely a one-time calculation, and a plan reviewed against real use stays accurate as the system and its loads evolve.

## Common sizing errors to correct early

One error is converting nameplate Ah directly to AC runtime without the DoD and inverter-efficiency steps; another is sizing only for average loads while forgetting startup inrush from compressors and motors. A third compares this LFP block against lead acid on raw capacity rather than usable energy after depth limits, and a fourth plans charging around an array or charger that cannot refill the daily draw before the next use, which gradually leaves the pack undercharged; working through the load list, the usable Wh band and the recharge source together gives a steadier picture of whether this 100Ah block matches the system.

It also helps to build in headroom rather than running the block at its edge every cycle, because a plan that leaves some spare Wh on quiet days is more forgiving when an appliance draws more than estimated, or when sunlight and refill are weaker than expected. The load list should be revisited after a season of real use, since actual consumption often differs from the initial estimate, and either load habits or bank size adjusted once real data is in hand.

## Sizing questions answered

### How much energy does this pack store?

At a 12.8V bus, 100Ah translates into 1280Wh stored on the DC side, which is the raw bus-level number arrived at before depth-of-discharge limits, inverter efficiency and any further conversion losses are taken off.

### How deep can I discharge the pack?

Cycle life is rated at 6000 cycles when depth of discharge reaches 80%, and for a long service life the plan should remain inside that usable band instead of draining to the 10V cut-off each cycle; the 10V point acts as a protection limit rather than an everyday working target.

### What usable energy should I plan for?

Work outward from 1280Wh DC, deduct the depth-of-discharge limit you settle on, and then allow for 90–95% inverter efficiency before AC runtime is estimated; what remains is the realistic AC energy that one charge can deliver.

### How can I work out how long my appliances will run?

Write down each load's wattage and daily hours, convert the sum into Wh, divide by the usable Wh that remain after your DoD band and inverter derating, and keep startup inrush in sight; the figure should be anchored to a representative day rather than to a single bright hour.

### Can this pack run high-power appliances?

The continuous DC ceiling sits at 100A, or 1280W before losses, and heaters, induction cookers and large air-conditioning units generally call for a larger bank; high-draw devices deserve to be sized against a bigger system as a separate exercise.

### Does the 400A pulse affect runtime planning?

It does not. The pulse covers a one-second startup inrush only, and steady runtime has to be planned from the 100A continuous limit; a brief compressor start draws little meaningful Wh, yet it has to remain inside the pulse window.

### How many cycles can I expect?

Expect 6000 cycles at 80% DoD, roughly 5000+ at a full 100% DoD, alongside an approximate ten-year design life, because shallower and more frequent charging and discharging generally keep cell condition intact over the long term.

### Should I size one pack or several?

When daily Wh demand climbs above the usable energy of a single unit, plan a documented multi-unit bank reaching 4P4S — 16 units at 20.48kWh — with identical units matched together, and beginning with one block still leaves room to add more later.

### What solar input suits this pack?

An MPPT controller placed on the 14.4V LFP profile is the solar route; because the spec sheet records no maximum panel wattage, the array and controller should be sized to your daily demand, with limits confirmed against the seller.

### Why do lead-acid comparisons overstate what this pack can do?

Lead-acid packs are frequently held within a 50% DoD band, whereas this LFP unit can draw on a deeper share of its store, so a nameplate Ah comparison that ignores usable depth misleads; the right comparison is usable Wh after your chosen DoD.

[Matching the Gsike 12.8V 100Ah LFP Pack to 12V Inverters, Chargers and Appliances in Spain](https://gesike.com/blogs/news/en-es-gsike-blog-1-voltage-pairing-use-cases)

[Everyday Scenarios for the Gsike 12.8V 100Ah Pack: Campervan, Boat, Rural Cabin and Evening Home Reserve](https://gesike.com/blogs/news/en-es-gsike-blog-3-offgrid-rv-backup-scenarios)

[Installing the Gsike 12.8V 100Ah Pack: M8 Terminals, Cable Sizing, Fuses and Bank Expansion Steps](https://gesike.com/blogs/news/en-es-gsike-blog-4-wiring-install-guide)

Size the system from daily Wh demand: take 1280Wh DC, apply your DoD band and 90–95% inverter efficiency, hold steady loads below 100A (1280W DC), and move to a matched multi-unit bank only once demand clearly outgrows one block.

[battery sizing, 1280Wh runtime, depth of discharge LFP, usable energy off-grid, Gsike 100Ah sizing, solar battery calculation](https://gesike.com/en-es/products/gsike-12-8v-100ah-lifepo4-battery-1280wh-off-grid-pack-spain)

**Tags:** 1280Wh runtime, battery sizing, depth of discharge LFP, Gsike 100Ah sizing, solar battery calculation, usable energy off-grid

---

> Source: [Gsike](https://gesike.com/blogs/news/en-es-gsike-blog-2-battery-sizing-comparison)
