Battery SizingRuntimeDepth of DischargeOff-Grid Planning

Sizing the Gsike 12.8V 100Ah Battery: Watt-Hours, Depth of Discharge and Runtime for Slovak Off-Grid Plans

This walkthrough sizes the Gsike 12.8V 100Ah pack from your real appliance list: daily watt-hours first, then depth-of-discharge and inverter losses, so you can judge whether a single 1280Wh unit or a matched bank suits your Slovak setup.

Start from daily watt-hours, not the amp-hour label

Sound off-grid planning starts from the energy your loads actually consume over a typical day, expressed in watt-hours, rather than with the amp-hour figure printed on the battery. Amp-hours only describe capacity at a given voltage, while the appliances you run are rated in watts, so multiplying watts by hours gives the watt-hours that match the pack's 1280Wh; because two setups can carry the same 100Ah label yet demand very different energy, the load audit is what tells you whether one pack suffices.

Frame the load list around a typical day rather than the best-case one: a campervan in summer may run lights, charging and a fridge for a weekend, while a winter cottage draws lighting and communications gear after dark, and a boat day mixes a trolling motor in intervals with lights and USB charging. Note which devices run at the same time, because the simultaneous steady current — not the total over the whole day — sets the continuous current requirement against the 100A, 1280W DC ceiling.

Keep DC loads apart from AC loads before totalling, because inverter efficiency applies only to the AC side: a 12V LED strip or USB socket draws direct energy from the bus, whereas a 230V appliance first passes through the inverter, losing a few percent in conversion, and keeping the two groups apart keeps the Wh arithmetic honest and makes the later runtime estimate defensible.

Workbench load list beside the Gsike 12.8V 100Ah battery

Building the load table from real appliances

The best sizing document is a simple load table built from your actual appliances rather than from generic estimates. For each device, record its running wattage, its DC or AC connection, its startup draw if the manual lists one, and the hours it runs in a typical day, and flag devices that run together so the simultaneous steady total can be checked against the continuous current limit rather than the daily Wh total alone.

Appliance Connection Running watts Daily hours Daily Wh
LED lighting DC 12V Per strip / bulb Evening hours Watts × hours
USB / device charging DC 12V Per port or hub Charging sessions Watts × hours
Compressor fridge DC 12V Average cycling draw 24h cycling Average watts × 24
Small water pump DC 12V Running watts Intermittent use Watts × hours
Router / laptop AC via inverter Appliance label Use hours Watts × hours ÷ efficiency
Trolling motor DC 12V Throttle-dependent draw On-water intervals Average amps × 12.8V × hours

Reading appliance labels correctly avoids two common slip-ups: some devices print input current rather than wattage, so multiply current by the operating voltage to get watts, while others list a peak or startup figure that is not the running draw. Where the label gives only an amperage, use the device's nominal voltage in the multiplication, and keep the startup figure separate for the inrush check against the one-second 400A pulse.

The fridge's cycling usually forms the largest repeating load in a leisure van, so its average daily Wh deserves a careful look rather than an estimate. A compressor fridge spends part of the hour running and the rest idle, and its average draw sits well below the momentary compressor wattage, which is why real cycling should be observed over a couple of days if you can; an overestimated fridge draw can make a modest setup look like it needs a second pack when one would suffice.

Depth of discharge: how far down the pack should go

LFP depth of discharge behaves differently from traditional lead-acid: many lead-acid banks are kept within a 50% DoD band to preserve life, whereas this lithium pack is rated to 6000 cycles at 80% DoD, with roughly 5000+ cycles expected at a full 100% draw. That means the usable band can be planned around 80% without the conservative headroom lead-acid demands, although deeper daily use does trade some cycle count for capacity.

Keeping DoD headroom protects cycle life: planning to stay around the 80% DoD band rather than draining to the 10V cutoff each evening keeps cells in the gentler part of their working range and supports the long design life. A plan that leaves some spare Wh on quiet days is more forgiving than one that runs the pack to its edge every cycle, because it absorbs the occasional heavier day without reaching the protection cutoff.

The BMS ends discharge at the 10V end-of-discharge point to protect the cells, which means that point is not a target to run down to on a regular basis. State of charge should be read from the inverter, charger or an external meter, since this model lists no on-pack screen or app, and if your daily plan repeatedly pushes close to that cutoff, it is a signal that the load list or the pack size needs revisiting rather than a reason to rely on the protection each evening.

Battery mounted in a ventilated locker with cable connections

Inverter efficiency and the runtime calculation

With the daily Wh total known, two reductions apply before comparing it to the 1280Wh stored energy: first, the chosen DoD band defines how much of the stored energy you plan to draw, and second, any AC portion passes through the inverter, which converts at roughly 90–95% efficiency. Multiplying the DC energy by that efficiency gives the realistic AC watt-hours, and sizing from the raw 1280Wh without these steps overstates what the pack can deliver.

Watt-hours per day equal running wattage times hours of use, added across all loads, and it is also worth marking which devices run at the same time so the steady current can be totalled separately. A simple sanity check compares the planned daily draw against the usable band across several days rather than one; if the plan regularly leaves the pack near empty, add capacity or trim loads before the first trip.

Step What to apply Figures recorded for this pack
Stored energy Nominal voltage × capacity 12.8V × 100Ah = 1280Wh
Usable by DoD band Share of stored energy planned for daily draw Plan around the 80% DoD band for cycle life
AC conversion loss Apply inverter efficiency to AC loads only Typical 90–95% inverter efficiency
Steady current check Sum devices expected to run together 100A continuous, 1280W DC ceiling
Startup inrush check Brief compressor or motor burst 400A for one second only

One handy check compares the planned daily draw against the pack's usable band across several days rather than one: if the plan regularly leaves the battery near the protection cutoff, the system either needs a larger store or fewer loads, whereas if most days finish with substantial spare Wh, the pack has comfortable headroom for occasional extra devices.

Worked examples for Slovak off-grid setups

Consider a moderate campervan day as an illustration: LED lights for several evening hours, phone and tablet charging, a portable fridge cycling through the day, and occasional USB or laptop use. These are DC-dominated, modest draws that sit inside the small-off-grid range this pack serves, and although the load table decides the exact Wh, the 1280Wh store with an 80% planning band covers a weekend in many such vans; the steady current should still be checked so the combined running devices stay under 100A.

The second example covers a boat day on the water: a trolling motor running in intervals across the day, plus lights and USB charging for accessories. Here the motor's throttle-dependent current drives the arithmetic, and runtime depends on throttle use, wind and water conditions, so match the motor's published draw at typical settings to the 100A continuous discharge and the 1280Wh store, leaving margin for wind or current that pushes the motor to a higher throttle for longer stretches.

In a rural cottage or garden shed on a modest panel array, the store backs evening lighting, communications gear and small appliances after dark. Where the outbuilding runs only low-power DC lighting and communications, one 1280Wh pack may cover the evening demand, whereas where a fridge, a pump or repeated AC appliances join the list, the daily Wh can outgrow that single unit and point toward an expanded bank.

Solar array feeding the battery in a rural Slovak setting

When one pack is enough, and when to expand the bank

This 1280Wh pack suits best where demands stay in the small-off-grid range: a weekend van leisure circuit, a small boat and trolling motor for a day on the water, a modest solar cottage and an evening reserve for essential household loads. Within those roles it covers LED lighting, USB and device charging, a portable compressor fridge, a small pump, a router and a laptop without approaching the continuous ceiling in normal use.

If daily demand outgrows one 1280Wh pack, the documented expansion reaches 4P4S — 16 units forming a 20.48kWh bank, with 4S reaching 51.2V and 4P giving 400Ah. Battery units must be identical and matched within about a month of production and charge history, because mixing fresh and worn cells is not advised, and expansion also means revisiting the inverter, charger or MPPT and the protection, since the new bus voltage and capacity change the whole system's arithmetic.

When the first real-use season shows demand outgrowing the single pack, the documented expansion path adds matched identical units up to a 4P4S, 20.48kWh arrangement. Before adding units, revisit the load table with real data — actual fridge cycling, real charging hours and any appliances added or removed — because a measured second season gives a firmer basis for how many extra units the bank needs than a best-guess estimate on day one.

Moving to a larger stored-energy solution makes sense when the system moves toward full-time van or boat living, runs multiple appliances together, or keeps high average draws across the day. A second or third pack, wired into a matched bank, shares the steady current and raises the daily Wh available, while series wiring raises bus voltage and parallel wiring raises capacity, and the inverter and charger must then suit the resulting configuration.

Common sizing errors and how to avoid them

A common error converts nameplate Ah directly to AC runtime without the DoD and inverter efficiency steps, and another is sizing only for average loads and forgetting the simultaneous steady current, which can approach the 100A ceiling even when the daily Wh looks modest. A third is treating the 400A pulse as available for steady running, which understates the real continuous limit the bank must meet.

A fourth mistake is running down to the 10V cutoff each evening, which leaves no headroom and shortens cycle life compared with the 80% DoD band the rating is built around. Overestimating an appliance's average draw can push a plan toward extra capacity that was never needed, while underestimating the fridge or pump can leave the pack flat before the trip ends, which is why recording real device data over a couple of days is the most reliable countermeasure either way.

Keep in mind the pack's own storage conditions between uses: self-discharge stays under 3% per month, but seasonal storage should still keep the block at roughly 50% charge in a dry, ventilated spot between −10°C and 50°C, checked every few months through a low-voltage or state-of-charge reading. A pack left deeply discharged through a long off-season is harder to bring back to a healthy state than one stored with partial charge and a periodic check.

Revisiting the plan after the first season

Once a season has passed, review the load table against real data: actual fridge cycling, real charging hours, and any appliances added or removed. Compare the observed daily Wh against the usable band of the pack and note how often the system ran near the cutoff, and that real usage record shows whether the single pack has spare capacity, matches the demand closely, or calls for a matched expansion later.

A well-matched store works with a refill source that can restore the day's draw before the next cycle. In a solar setup, the MPPT controller must carry the 14.4V ±0.2V LFP profile and enough current for the array, and where solar alone cannot cover the draw — a winter cottage with short days, or a van on a cloudy stretch of travel — a shore or mains LiFePO4 charger may be needed to top the bank up before the next period of use.

Working through the Wh, DoD and current numbers

The 1280Wh figure is 12.8V times 100Ah, the energy held at the DC bus before any conversion, and when an inverter turns that DC into AC, its 90–95% efficiency means the appliance receives a little less than the bus total. Sizing AC runtime straight from the bus Wh ignores that loss and overstates how long the load will run.

The 6000-cycle figure is rated around an 80% depth of discharge, so the dependable working band sits near 80% of capacity rather than draining every amp to the cutoff, and keeping draws inside that band preserves cycle life while regular runs toward the ~10V discharge cutoff shorten the healthy cycle count even though the BMS guards against undervoltage.

Leisure loads split between small DC draws and occasional AC uses: LED lights, USB charging and small DC pumps take modest daily amounts, a cycling 12V fridge often sets the daily baseline, and AC appliances pass through the inverter and carry the efficiency loss. Listing each device's watts and daily hours turns a rough 'enough power' hunch into a daily Wh total comparable with the usable band.

Energy and current are checked separately: a 1280Wh store can still be too small for a short heavy draw if steady current climbs toward 100A, and a low-energy but high-wattage appliance hits the current ceiling despite a small daily Wh, so compare daily Wh against usable energy and simultaneous steady amps against the 100A / 1280W DC limit.

A single 1280Wh unit covers weekend use, modest leisure loads and short evening reserves, and the documented 4P4S bank, up to 16 units for 20.48kWh, is added when measured daily Wh exceed the single unit's usable band, several devices run together, or refill cannot reliably restore the draw. Units must be identical and matched in production and charge history, since fresh and worn cells are not combined, and Slovak setups around Bratislava, the Danube lowland, the High Tatras, Liptov and Orava should size from recorded local device hours, confirming delivery cost, duties, VAT and after-sales with the seller because the listed free-delivery terms cover only the 15 named EU markets.

A measured load record beats a guess at the planning stage: note each device's wattage, how many hours a day it runs, and which ones run at the same moment, and once the daily Wh and the simultaneous steady amps are written down, compare them against the pack's usable energy band and the 100A / 1280W DC ceiling. If the busiest ordinary day stays comfortably inside both, one 1280Wh unit is a sound choice; if either number sits near the limit, a matched expansion bank is the safer direction before committing to the install.

Sizing questions answered

How do I estimate the energy my setup uses each day?

Multiply each device's running watts by its hours in a typical day and sum the watt-hours, keeping DC and AC loads separate because inverter efficiency applies only to the AC side.

How much energy is left from a 1280Wh pack after depth of discharge?

Planning around an 80% DoD band protects cycle life; cells can go deeper, but that shortens the cycle count, and on top of that AC runtime is reduced by the inverter's 90–95% efficiency.

How does inverter efficiency lower the runtime?

A 12V inverter in this class converts at roughly 90–95%, so available AC watt-hours equal the DC stored energy times that efficiency; size from the reduced AC figure rather than the raw 1280Wh.

How long will the battery run my fridge?

It depends on the fridge's average daily watt-hours and compressor cycling rather than the nameplate alone, so record real running hours and draw over a couple of days, then compare with the usable band.

Does 100Ah cover a campervan weekend?

It can cover modest LED lighting, USB charging and a compact fridge over a weekend, whereas heavier appliances, longer trips or simultaneous high draws push toward a bigger bank; the load list decides rather than the Ah label.

What depth of discharge should the plan target?

The 6000-cycle rating is recorded at 80% depth of discharge, and planning to that band keeps the long cycle life, while repeated full 100% draws expect roughly 5000+ cycles, so deeper use trades some cycle count for capacity.

At what point should I add a second pack?

Add units once the daily Wh demand exceeds the single pack's usable band, or when the simultaneous steady current nears the 100A continuous limit; the documented expansion reaches 4P4S, a 20.48kWh bank of matched identical units.

Can old and new batteries be mixed in an expansion?

No. Joined batteries must be identical and matched within about a month of production and charge history, so fresh and aged cells are neither paralleled nor series-connected together.

Does self-discharge eat into my stored energy?

Self-discharge stays under 3% per month, which is modest for seasonal use, and between trips the pack should be stored at roughly 50% charge in a dry, ventilated spot within −10°C to 50°C, checked periodically.

What runtime figure should I put in the plan?

Work from average daily watt-hours, the chosen DoD band and inverter efficiency, and keep spare Wh on quiet days; do not quote a runtime built only from the nameplate Ah or the best-case appliance draw.

Work from recorded daily watt-hours, hold the plan near the 80% DoD band, deduct the inverter's 90–95% efficiency on AC loads, and check the simultaneous steady current against the 100A / 1280W DC ceiling before choosing one pack or a matched expansion.

battery sizing Slovakia, 1280Wh runtime, depth of discharge LFP, off-grid Wh calculation, campervan battery capacity, Gsike 100Ah sizing