Gsike TELLUS-T300 Power Plant Portable for a Campervan Electrical System Build
How a 297 Wh compact station fits into a small van 12 V build, covering interior lights, roof fan, water pump, laptop and phone loads, DC-DC and solar recharge, and the appliance limits of the 300 W tier.
The direct answer: the Gsike TELLUS-T300 Pro is a 297 Wh, 300 W continuous LiFePO4 portable power plant that works as a compact supplementary 12 V source in a campervan build for LED interior lights, a roof fan, a small water pump, phone and tablet charging, and a laptop session, with 120 W total DC output, two side AC outlets, four refill routes, and a 5.05 kg, about 11.1 lb body that stows under a bed or beside a storage cubby. The official Gsike US store carries the unit for $339.00 USD.
This guide is written for people planning or building a campervan, conversion van, or small camper where a full wired-in house battery bank is more than the layout needs, or where a second portable reserve is wanted alongside the main system. It explains how a freestanding station slots into a 12 V electrics layout, which van loads it realistically covers, how Wh converts to usable amp-hours at 12 V, and how it recharges from the van alternator, a panel, a wall outlet, or USB-C.
The unit stores 297 Wh, labeled 72,000 mAh, and delivers 300 W continuous pure sine wave 110 V through two side NEMA 5-15R outlets. Its manufacturer has not published a peak or surge figure, so planning in this guide uses the 300 W continuous rating only, without quoting a startup number. The DC side carries 120 W total at 12 V/10 A across the cigarette-lighter jack, DC5521, and DC5525 connectors.
Where a portable station sits in a van 12 V layout
A campervan electrics system usually combines a starting battery for the engine, a house battery for living loads, a charging path from the alternator and solar, and a fuse or distribution block that splits 12 V to lights, fan, pump, and USB points. A portable station acts as a movable secondary battery in that layout: it stores its own 297 Wh, supplies its own outputs, and can be removed when the van returns to daily use.
- Supplementary reserve rather than a fixed bank. For a small weekend van or a starter build, the station can carry the living loads on its own without wiring a permanent multi-cell bank into the van. In a larger conversion, it works as an extra reserve for specific devices or a dry-camp backup beside the main house battery.
- Separate DC and AC outlets. The 12 V DC bank feeds 12 V van gear directly, while the two NEMA outlets run AC devices such as a laptop brick or a small charger. USB-C, USB-A, and the wireless pad cover phones and tablets without an adapter.
- No permanent modification required. Because the unit is freestanding, it does not need custom battery-box fabrication, vented enclosure work, or a fixed busbar to be functional. Connections are made through plugs and adapters rather than a welded-in circuit.
- Readable state of charge. The LCD display shows remaining reserve and load status, which helps a van builder pace a dry-camp day and see which circuits are drawing the most energy.
- Removable for off-van use. The 11.1 lb body and carry handle let the station leave the van for a picnic spot, a beach trip, or a home desk, which a fixed under-bonnet or under-seat house battery cannot do.
This role is complementary to a properly sized house system. A van built for multi-week off-grid living with a compressor fridge, heater, and cooktop will eventually outgrow a single 297 Wh station, and the sections below mark where that limit appears.
Van 12 V loads and 297 Wh expectations
Build planning works best when each van circuit is matched to its draw, then compared against the verified pack figures. The table below lists common campervan living loads, their typical wattage, and what the 297 Wh T300 Pro can realistically deliver. Figures are planning references under normal efficiency losses; actual results shift with runtime, settings, and how many circuits run together.
| Van living load | Typical draw | Expectation on 297 Wh | Connection note |
|---|---|---|---|
| LED interior lights (several) | 5–15 W total | Many hours of evening lighting | Low-wattage 12 V circuits on the DC bank |
| Roof or van fan | 10–25 W | A few hours of ventilation | DC accessory; cycles with temperature and airflow |
| Fresh-water pump | 10–30 W, intermittent | Short cycling through hand washing and cooking water | Intermittent duty, not continuous run; check pump label |
| Phone (10 Wh battery) | Charging only | 29+ full charges | USB-A, USB-C, or wireless pad |
| Tablet / e-reader | 5–10 Wh per charge | Several charges per pack | Share a USB slot while other circuits run |
| 60 W laptop | 60 W running | 4.5+ hours | Best fed by the 100 W USB-C PD route over one cable |
| Small 12 V compressor fridge | 30–100 W cycling | Limited daytime cover; check cycling duty | Compressor cycles off and on; a full overnight fridge needs a larger bank |
| Heater, induction cooktop, microwave | Well above 300 W | Not supported at the continuous ceiling | Leave these on a dedicated larger system or separate fuel appliance |
The light living loads are where the compact pack performs best. Interior LEDs, a fan, intermittent pump use, phone and tablet topping-up, and a laptop session all sit comfortably within the station's output limits for a weekend van trip. The verified phone and camera counts show how the reserve spreads across small batteries when they charge in short bursts between uses.
Add the running watts of everything expected to run at once and keep the AC total under 300 W and the DC total under 120 W. Lights plus fan plus phone stay comfortably under both; a compressor fridge running alongside a fan and a laptop deserves a closer look at the combined draw and the pack's cycling behavior.
Converting 297 Wh to usable amp-hours at 12 V
Van builders often size battery systems in amp-hours rather than watt-hours, so it helps to translate the pack into 12 V terms before matching it to a fuse block or accessory circuit.
- The basic conversion. Dividing stored watt-hours by nominal voltage gives amp-hours: 297 Wh ÷ 12 V works out to roughly 24.8 Ah at a nominal 12 V figure. This is a label-level conversion, not a fully available deep-drain capacity.
- Apply an efficiency derate. Inverter conversion, charging losses, and protection limits mean the usable portion sits below the rated 297 Wh and below that nominal Ah figure. Plan around a conservative portion of the pack rather than spending the full 24.8 Ah in one session.
- Match fuse and cable to the DC side. The 12 V DC bank is limited to 120 W total, about 10 A at 12 V. Any DC circuit fed from the station should use appropriately sized cable and a protected adapter or inline fuse so a short on a van wire does not trace back to the unit's BMS.
- Track daily Wh rather than Ah alone. Van living loads are easiest to plan in watt-hours: list each device's watts, estimate daily hours, sum the Wh, and compare against the 297 Wh reserve plus whatever solar or alternator recharge the day provides.
For a weekend van, a realistic daily living load of lights, fan, pump, phone, and occasional laptop use can fit the compact reserve with careful pacing. A build that runs a compressor fridge continuously through several nights, or several high-draw appliances together, will need a larger house battery and inverter than this station provides.
Recharging the van station: alternator, solar, wall, and USB-C
An electrics build lives or dies on its charging loop, and the T300 Pro offers four refill routes so the reserve can recover while driving, parked in sun, or plugged in at a stop.
| Refill route | Input on the T300 Pro | Typical refill time | Van build scenario |
|---|---|---|---|
| Vehicle / alternator outlet | 12 V/24 V, 8 A car input | About 3–4 hours | Top up during driving days between stops |
| Solar panel | Up to 120 W DC solar input | About 2.5–3 hours in good sun | Dry-camp daytime harvest through a roof or portable panel |
| Wall AC outlet | 300 W fast charge through the AC input | About 1 hour to full | Fast refill at a campsite hookup, depot, or home |
| USB-C PD | 100 W USB-C PD input | About 3 hours | One-cable top-up from a compatible charger or power source |
The alternator route feeds the pack through the vehicle outlet while driving, which suits a van that moves between locations; note that a dedicated DC-DC charger and isolation wiring are part of a permanent house-battery install, while this station refills through its own car input rather than wiring directly into the vehicle's charging system.
Solar keeps the reserve topped during dry camping, up to the 120 W input ceiling; real yield depends on panel angle, roof shade, weather, and panel condition, and the panel itself is not included in the box. The wall route is the fastest recovery for a drained pack, and USB-C PD gives a cable-only option where a charger is available. The station also supports simultaneous solar plus grid charging, so sunlight and a wall source can combine during a refill.
Mounting, storage, and cable routing in the van
A portable station in a moving van needs a secure spot, clear ventilation, and tidy cables that do not become a hazard on rough roads.
- Choose a fixed, low-vibration spot. Under a bed bench, beside a storage cubby, or on a secured shelf keeps the weight low and the unit out of walking paths. Strap or bracket it in place so it cannot slide during driving or on uneven campsite ground.
- Leave ventilation around the vents. The active cooling fan needs airflow around the case, so do not seal the unit inside an airtight cubby or pile bedding and gear against its vents. A small gap on all sides protects the cooling path.
- Route DC cables away from pinch points. Keep leads clear of closing doors, sliding tracks, and moving parts, secure them with clips, and keep connector ends dry and above any possible floor water. Fuse accessory circuits at the station or distribution end.
- Keep it accessible for the display and handle. The LCD readout and carry handle should be reachable so the reserve can be checked and the unit removed without unpacking the whole bed area.
- Watch moisture and temperature. The IP21 rating covers basic solid-object and drip protection, not wet mounting or wash-down. Keep the station away from sink and shower splash, and bring it to a moderate temperature before a long charge after a cold night.
The integrated LED bar in the carry handle adds an interior or camp light without a separate lantern, switched independently of the power outputs. It helps with overnight bed access and evening setup at the site, though dedicated van interior lighting remains the main circuit for steady interior illumination.
Which van appliances still need a larger inverter or battery
The 300 W continuous ceiling and 297 Wh reserve define the boundary of this compact tier, and some common campervan appliances sit clearly on the other side.
Heaters, induction cooktops, microwave ovens, and high-power compressor fridges typically draw several hundred watts or run continuously for long periods, exceeding both the 300 W continuous output and the 297 Wh capacity. These belong to a larger house battery and inverter system, or to a separate fuel appliance, rather than this portable station. Do not connect a high-draw appliance expecting the compact pack to sustain it.
A small 12 V fan, LED lighting, and an intermittent pump are well within the DC bank's 120 W limit. A small compressor fridge is the borderline load: its cycling duty can stretch a short daytime cover, but an overnight fridge running through several nights usually demands a deeper battery than 297 Wh. Check the fridge label's running watts and duty cycle before planning it as a daily load.
Because no peak figure is published for the T300 Pro, startup-sensitive motor loads are sized conservatively against the continuous rating. When a device has an internal compressor or fan, read its own startup current on the label rather than assuming hidden surge headroom in the pack.
Battery chemistry, cycle life, and protection for a frequent van charger
A van build recharges its reserve repeatedly between trips, so cell longevity and protection matter as much as the initial capacity. The T300 Pro uses LiFePO4 cells rated for 3,500+ cycles to at least 80% remaining capacity, with a design life around ten years under normal use, which suits a station charged often across seasons of travel.
- Eight-protection BMS. The management system watches large-capacity operation, cooling, overcharge, low voltage, overload, overheating, short circuit, and low temperature, working to keep the cells within safe limits through repeated loops.
- Active cooling and readout. Active cooling manages heat during charge and discharge, while the LCD display shows state of charge and load so the builder can monitor the van circuits in real time.
- Pure sine wave output. The inverter delivers a clean 110 V pure sine wave, the waveform preferred for laptops, charging circuits, and sensitive electronics, avoiding the choppy delivery that modified sine wave inverters can produce.
- UPS transfer for sensitive devices. UPS mode switches over within under 10 ms when an input source drops, helping a connected laptop or network device avoid a hard reset during a brief interruption. This covers the transfer and a short reserve window rather than an unlimited stay-on period.
- Long-storage care. Between travel seasons, store the pack at a moderate charge in a dry, moderate-temperature spot rather than fully depleted, and follow the manual's storage guidance for layovers.
LiFePO4 chemistry runs cooler and more thermally stable than older NMC designs, which fits a unit kept inside a living space in the van. The chemistry does not enlarge the reserve, however, and it does not replace proper fusing, ventilation, or matching the load to the 300 W and 120 W limits.
The Gsike TELLUS-T300 Pro portable power plant is listed at $339.00 USD on the official Gsike US store.
Frequently Asked Questions
How does a portable station fit into a campervan 12V build?
It acts as a freestanding supplementary battery: storing 297 Wh, supplying its own DC and AC outputs, and connecting through plugs and adapters rather than a wired-in bank. In a small weekend van it can carry the living loads on its own; in a larger conversion it adds a movable reserve beside the main house battery.
Which 12V van loads run off the T300 station?
It covers LED interior lights, a roof or van fan, an intermittent fresh-water pump, phone and tablet charging, and a laptop session within the 300 W continuous AC ceiling and the 120 W DC bank. Compressor fridges are a borderline cycling load; heaters, cooktops, and microwaves are outside this tier.
What Ah capacity corresponds to 297Wh at 12V?
297 Wh divided by a nominal 12 V works out to roughly 24.8 Ah at label level. Apply an efficiency derate for inverter and charging losses before planning deep use, and keep the DC circuits within the 120 W, about 10 A limit. Track daily watt-hours rather than relying on the nominal Ah alone.
How do you recharge the van station from the alternator or solar?
The vehicle outlet takes about 3–4 hours from a 12 V/24 V 8 A source; solar up to 120 W takes about 2.5–3 hours in good sun; wall fast charge takes about one hour; and 100 W USB-C PD takes about three hours. Sunlight and mains feed can combine, and a solar panel is not included in the box. A permanent house-battery DC-DC install needs its own charger and isolation wiring.
Can it run a van fridge, fan, and water pump together?
A fan and intermittent pump share the DC bank comfortably with lights and phone charging. A small compressor fridge adds cycling draw that shortens the day's cover, so add its running watts to the combined load and check the duty cycle. An overnight fridge through multiple nights generally needs a deeper battery than 297 Wh.
Which van appliances still need a larger inverter or battery?
Heaters, induction cooktops, microwaves, and high-power compressor fridges usually exceed the 300 W continuous ceiling and the 297 Wh reserve. These belong to a larger house battery and inverter system or a separate fuel appliance; do not connect them expecting the compact station to sustain the load.
Where should the station be mounted or stored in a van build?
Use a secured low spot under a bed bench, beside a storage cubby, or on a fixed shelf, strapped so it cannot slide. Leave ventilation around the vents, route cables away from pinch points and moisture, and keep the display and carry handle reachable for reserve checks and removal.
How does DC wiring and fuse protection connect to the station?
12 V accessories connect through the cigarette-lighter jack, DC5521, or DC5525 connectors on the 120 W, 12 V/10 A DC bank. Match the adapter and polarity, use an appropriately sized inline fuse for the accessory circuit, keep combined DC draw under 120 W, and secure cables away from closing parts and standing water.
Is the LiFePO4 pack suited to frequent van charging cycles?
Yes. The pack is rated for 3,500+ cycles to at least 80% remaining capacity with about a ten-year design life, and the eight-protection BMS plus active cooling support repeated charging between trips. LiFePO4 also runs cooler and more thermally stable than older NMC designs inside a living space.
Where does the $339.00 compact station fit a campervan electrical build?
It fits a small weekend or starter van build carrying lights, fan, pump, phone, tablet, and a laptop session, or a movable extra reserve in a larger conversion. It is not a substitute for a deep house battery running continuous fridge, heating, or cooking loads; those call for a larger battery and inverter system sized to the build.
Conclusion
For a van builder, the Gsike TELLUS-T300 Pro turns a 297 Wh compact pack into a portable 12 V living source: it runs interior LEDs, a fan, an intermittent pump, keeps phones and tablets topped, and covers a laptop session, with recharge from the driving alternator, solar, wall, or USB-C and a 11.1 lb body that stows under a bed or cubby. Its freestanding format suits small weekend conversions and supplementary reserve without a fixed battery-box installation.
The limits are clear as well: this tier supports low-and-medium living loads for a paced weekend, not continuous fridge, heating, or cooking duty, and a multi-week off-grid build needs a deeper house battery and larger inverter. Within that scope, the station gives a van build a flexible, removable source that can leave the vehicle for other trips.
Article Keywords: campervan portable power plant, van 12V electrical build battery, campervan 12V system station, 297Wh van life battery, 300W portable power plant, Gsike TELLUS-T300 Pro, power plant portable, portable power station, DC-DC van recharge station, LiFePO4 campervan battery, small van build power station, Gsike power plant portable
