12V Marine Power Fishing & Boating Electronics Console & Dock Support

Gsike TELLUS-T300 Power Plant Portable for Fishing and Boating: 12V Marine Power

How a 297Wh compact battery plant supports a fish finder, chartplotter, nav light, phone, and camera on the water, with 12V accessory runtime, onboard placement guidance, and recharge routes between trips.

The short answer: the Gsike TELLUS-T300 Pro is a 297 Wh, 300 W continuous LiFePO4 portable power plant built to supply the low-wattage electronics and accessories anglers and boaters rely on away from the dock, with 120 W total 12 V DC output, two side AC outlets, USB-C and USB-A charging, and a 5.05 kg, about 11.1 lb body that rides on a console or under a seat. It is listed at $339.00 USD on the official Gsike US store.

This guide is written for people who fish from small boats, kayaks, jon boats, and pontoons, and who keep a skiff or dinghy tied at a dock: anyone whose day on the water depends on a sonar unit, GPS chart, phone navigation, camera shots, and maybe a small fan or light staying charged while the motor's own starting battery is reserved for the engine. It maps each typical marine accessory to its draw, sets a day-on-water energy budget against the 297 Wh pack, and marks where the station's role ends.

The unit stores 297 Wh, labeled 72,000 mAh, and outputs 300 W continuous pure sine wave 110 V across two side NEMA 5-15R outlets. Its manufacturer has not published a peak or surge figure, so this guide sizes loads to the 300 W continuous rating only, without assigning a startup number. The DC side supplies 120 W total at 12 V/10 A across the cigarette-lighter jack, DC5521, and DC5525 connectors.

Compact Gsike T300 portable power plant mounted on a boat console beside a fish finder and navigation gear

Why a separate portable plant supports marine electronics instead of the starting battery

A boat's starting battery exists to crank the engine, and draining it for accessories can leave you stranded with a motor that will not turn over. A dedicated portable plant keeps electronics on its own stored reserve, protecting the starting battery for the one job it must do, which is the core reason small-boat anglers add a second power source.

  1. Reserve for the engine start. Keeping sonar, phone, and camera off the starting battery means the engine battery retains charge for cranking at the end of the day, especially after a long trolling or idle session that would otherwise pull it down.
  2. Mixed DC and AC outputs in one box. The 12 V DC bank runs 12 V accessories directly, while the two NEMA outlets feed AC chargers such as a phone brick or camera battery charger, so one unit replaces a loose collection of small adapters and power banks.
  3. Clean waveform for sensitive gear. The pure sine wave 110 V output treats sonar heads, chartplotters, and charging circuits more gently than a choppy modified sine wave feed, which helps avoid glitches on sensitive marine electronics.
  4. Carry between boats and the dock. At 11.1 lb with a carry handle, the plant moves from console to dock table to truck bed, which suits anglers who switch between boats or share gear across trips rather than wiring a fixed second battery into one vessel.
  5. Readable reserve on a display. The LCD readout shows remaining state and load status, so you can pace a day on the water instead of guessing how much charge the accessories are drawing.

This second-source role is about electronics and small accessories, not propulsion. A trolling motor, windlass, or high-demand marine pump pulls a different class of current and belongs on a properly sized deep-cycle marine battery, which the sections below explain.

Boat and fishing accessory wattage on the 297 Wh pack

On-the-water planning works best when each accessory is matched to its own nameplate draw, then compared against the verified pack figures. The table below lists common small-boat gear, its typical wattage, and what the 297 Wh T300 Pro can realistically deliver. Figures are planning references under normal efficiency losses; actual results shift with screen brightness, transducer settings, running time, and how many accessories draw together.

Marine accessory Typical draw Expectation on 297 Wh Connection note
Fish finder / sonar head 10–30 W Many hours of continuous use Light draw that stretches the reserve alongside other electronics
GPS chartplotter 10–25 W Several hours of mapping and navigation Share the DC bank or AC outlet depending on device adapter
Navigation / anchor LED light 3–10 W Many hours through an evening session Low-wattage 12 V accessory fed from the DC jack
Smartphone (10 Wh battery) Charging only 29+ full charges USB-A, USB-C, or top wireless pad depending on phone
5 Wh camera / action cam battery Charging only 59+ charges Keep filming and photo gear topped between spots
60 W laptop (onshore planning) 60 W running 4.5+ hours Use at the dock or in the vehicle, not the primary boat load
Small 12 V fan 10–20 W A few hours of cockpit or enclosed-boat ventilation DC accessory run beside the electronics load
Intermittent live-well pump 10–30 W, cycles on and off Short intermittent support, not continuous duty Check the pump label; cycling draw stays within the pump's running rating
Trolling motor / high-demand pump Well above the 120 W DC bank Not supported by this station Run these from a dedicated deep-cycle marine battery instead

The light electronics are where the compact pack earns its place. A sonar unit, chartplotter, nav light, and phone together typically sit in the low-to-tens-of-watts range, so the 297 Wh reserve covers a full fishing day with reasonable pacing and room for camera top-ups. The verified phone and camera counts show how far the pack spreads across small batteries when those devices charge in short bursts between catches.

Add the running watts of everything you expect to run at once and keep the combined load inside the station's limits: 300 W continuous on the AC side and 120 W total on the 12 V DC side. A sonar plus phone plus small fan stays comfortably under both; stacking several high-draw 12 V accessories on the DC jack deserves a closer look at the 10 A current limit.

Angler beside a dock and small boat charging a phone and camera battery from a portable power station

Setting a day-on-water Wh budget before launching

A few minutes of budgeting at the ramp prevents arriving on the water with a half pack and no reachable shore power. The method lists the gear you will actually run, estimates its hours, and converts watts and hours into watt-hours against the 297 Wh reserve.

  1. Write down the real fishing gear. Sonar, chartplotter, nav light, phone, and camera are the typical small-boat list; leave any comfort or entertainment gadgets off the first-pass plan.
  2. Estimate each accessory's session length. A six-hour outing with the sonar and chart running most of the way, the phone topped once or twice, and a camera charged between spots are realistic placeholders to adjust to your own trip.
  3. Account for efficiency loss. Inverter and charging losses mean usable energy sits below the rated 297 Wh, so plan against a conservative portion of the pack rather than the full label number.
  4. Check the combined continuous draw. Add the running watts of everything powered at once, and keep the AC total under 300 W and the DC total under 120 W. Electronics plus a small fan fit those limits; a second high-wattage accessory should be confirmed against the DC current rating.
  5. Plan a refill window. Decide where the pack tops up between outings: a home wall outlet before launch, a vehicle outlet on the drive, or a portable panel in daylight on the shore or deck.

For a typical day on a small boat, the load is sonar and mapping through the outing, a phone kept available, and occasional camera topping-up. That mix fits the compact tier. A multi-day remote trip with lights, fans, and pumps running continuously, or any propulsion device, would push past this station's scope and call for a larger deep-cycle battery setup instead.

Connecting 12 V accessories to the portable plant

Most fishing and navigation gear runs on 12 V, and the station's DC bank is the natural connection point for that equipment. The 120 W total DC output at 12 V/10 A feeds a cigarette-lighter-style jack plus the DC5521 and DC5525 connectors, giving a few common plug types without a permanent wiring job.

12V marine cables and DC connectors running from a portable power plant to boat accessory sockets
  1. Match the connector and polarity. Confirm the accessory plug matches the jack or add a properly rated adapter, and verify positive and negative polarity before first connection, since reversed leads can damage a device.
  2. Respect the 120 W and 10 A limit. Add the wattage of DC accessories sharing the bank and stay under 120 W total; keep current within the 10 A rating on the DC side rather than plugging in several pumps or lights at once.
  3. Use a fuse or protected adapter where needed. Sensitive marine electronics benefit from an inline fuse on the accessory lead, matched to the device current, so a short on a cable does not trace back to the station's protection system.
  4. Route cables away from pinch points and bilge water. Secure cords along the console or under a seat so they are not trapped in a closing hatch or dragged through standing water, and keep connectors above the deck line where spray can reach them.
  5. Use AC only where the device requires it. Devices that charge over AC plug into the two side NEMA outlets; 12 V gear runs through the DC bank, and USB phones and cameras use the USB-C, USB-A, or wireless pad rather than an AC brick.

Because this station is portable rather than a wired-in marine battery, its connections are made at the start of a trip and removed at the end. That keeps the setup flexible across boats but means you should verify each adapter and fuse before launch rather than relying on a fixed, pre-wired circuit.

Trolling motors and other propulsion: what this station does not do

A trolling motor, anchor windlass, or high-demand deck pump draws a heavy, sustained current that a 297 Wh compact station cannot supply. These loads belong on a dedicated deep-cycle marine battery sized to the motor's thrust and amp rating, charged by the boat's charging system or a separate marine charger. The T300 Pro supports electronics and small accessories; it is not a propulsion battery and should not be wired to a trolling motor leads.

It can be hard to tell where an accessory ends and a propulsion load begins, so check the device's amp or watt rating before connecting. A small intermittent pump or light fan draws within the DC bank; a motor that moves the boat, lifts an anchor, or runs continuously at high current does not, and overloading that circuit can cut out the inverter rather than driving the device.

The station publishes no peak or surge figure, so startup-sensitive loads are sized conservatively against the 300 W continuous AC rating and the 120 W DC rating. For any device with a motor or internal compressor, read its own startup current on the label rather than assuming hidden surge headroom in the compact pack.

Saltwater, spray, and onboard placement safety

Marine environments add spray, humidity, vibration, and salt exposure that a household battery station was not designed to live in permanently, so placement and care matter more afloat than on a campsite.

  1. Treat the IP21 rating as sheltered use. The station carries IP21 protection against solid objects and vertical dripping, not against rain, spray immersion, or washing down with a hose. Keep it under a console canopy, inside a storage compartment, or behind a dash cover rather than on an open deck where waves and spray can reach it.
  2. Keep it dry and secured. Stow the plant where it will not slide across the floor in rough water, and keep it clear of the bilge, standing water, and direct spray from the washdown hose. A non-slip mat or strap holds the unit in place during movement.
  3. Watch salt residue and ventilation. Salt air leaves residue on vents and connectors, so wipe the case down after a saltwater trip and keep the cooling vents unobstructed. The active cooling fan runs while charging or under load; do not seal the unit inside an airtight compartment.
  4. Protect connectors from moisture. Cap unused DC and USB ports when not in use, and keep cable ends above deck level. Corrosion on a plug interferes with the connection and can heat up under load.
  5. Store onshore between trips. When the boat is laid up, bring the station home and store it at a moderate charge in a dry, moderate-temperature place rather than leaving it in an enclosed locker through a wet season.

Unlike a fuel-burning generator, the battery plant produces no exhaust or combustion, which makes it safe to run in an open cockpit or sheltered compartment where fumes cannot accumulate. That still does not turn it into a marine-rated sealed unit; keep it dry, ventilated, and secured, and follow the manual's guidance for any condition outside ordinary indoor or covered outdoor use.

Refilling the pack between fishing trips

Recharge on the water or at the ramp means matching the refill route to whatever source the trip provides. The T300 Pro offers four channels, so a drained pack can recover at home, in the driveway, or at a shore-side panel.

Refill route Input on the T300 Pro Typical refill time Boating use case
Wall AC outlet 300 W fast charge through the AC input About 1 hour to full Top up at home the night before an early launch
Vehicle outlet 12 V/24 V, 8 A car input About 3–4 hours Refill on the drive to the ramp or back from a remote launch
Solar panel Up to 120 W DC solar input About 2.5–3 hours in good sun Shore-side or deck topping-up during longer stays off the dock
USB-C PD 100 W USB-C PD input About 3 hours One-cable top-up from a compatible charger or power source

The wall route is the fastest way to recover a drained pack, and a roughly one-hour refill fits the evening before a planned outing. The vehicle route covers driving days and trips to remote ramps, while solar suits shore-side downtime in daylight; real solar yield depends on angle, shade, and weather, and the panel itself is not included in the box.

The station also supports simultaneous solar plus grid charging, so sunlight and a wall source can top the pack together when both are available. Between outings, keep the pack at a moderate charge rather than fully depleted, and follow the manual's long-storage guidance if the boat sits unused for weeks.

Ports, lighting, and the day-on-water accessory setup

The port spread decides how many fishing devices you can run without adapter chains, and the built-in light removes one extra accessory from the boat bag. Alongside the two side NEMA outlets, the station provides two USB-C ports rated 100 W and 30 W, two USB-A ports in the 18 W and 12 W class, a wireless charging pad on top, and the 120 W DC bank for 12 V gear.

The 100 W USB-C slot can feed a compatible laptop or high-power USB device over one cable, which is handy for reviewing maps or logs at the dock; the 30 W USB-C and USB-A ports share phones and smaller cameras, and the wireless pad holds a compatible phone off a wet console surface.

The carry handle houses an integrated LED light bar switched separately from the power outputs. It works as an evening navigation light, a dock-side rigging light, or a cockpit read when the sun goes down, without packing a separate lantern. The bar is supplemental lighting rather than a high-power running or deck light; dedicated navigation and anchor lights remain the required equipment on the vessel itself.

UPS mode transfers within under 10 ms when an input source drops, which helps a connected phone or charting device avoid a hard reset during a brief power interruption. That covers the transfer and a short reserve window; once the pack drains, connected accessories stop, so pace the day around the lightest essential gear when the reserve runs low.

The Gsike TELLUS-T300 Pro portable power plant carries a $339.00 USD price tag on the official Gsike US store.

Open the Gsike TELLUS-T300 Pro product page to confirm the current $339.00 price and review the full specification list.

Frequently Asked Questions

What fishing and boating electronics can the T300 power on the water?

It covers a fish finder or sonar head, GPS chartplotter, navigation LED light, smartphone, camera and action-cam batteries, a small 12 V fan, and intermittent light pumps within the 300 W continuous AC ceiling and the 120 W DC bank. Propulsion motors, windlasses, and high-demand deck pumps are outside this compact station's scope.

How many watts does a fish finder, chartplotter, and nav light draw?

A typical fish finder or sonar head runs about 10–30 W, a GPS chartplotter roughly 10–25 W, and an LED navigation or anchor light around 3–10 W. These are nameplate planning figures; check the actual device labels for your own electronics, and add the running watts of anything powered at the same time.

How long will 297Wh run a day-on-water electronics load?

On the verified pack, a 10 Wh phone receives 29+ charges, a 5 Wh camera battery 59+ charges, and a 60 W laptop 4.5+ hours. Light sonar, chart, and nav-light loads draw in the tens of watts and typically stretch through a full outing with conservative pacing; actual hours shift with screen brightness, settings, and how many accessories run together.

Can it run a trolling motor?

No. A trolling motor pulls a heavy, sustained current that this 297 Wh compact station cannot supply, and it belongs on a dedicated deep-cycle marine battery sized to the motor's thrust and amp rating. The T300 Pro supports electronics and small accessories only; it should not be wired to motor leads.

Does the 12V DC output connect directly to boat accessories?

Yes, within limits. The DC side supplies 120 W total at 12 V/10 A through the cigarette-lighter jack, DC5521, and DC5525 connectors. Match the plug and polarity, add a properly rated inline fuse where the device warrants one, and keep the combined DC load under 120 W and within the 10 A current rating.

Is the station safe near saltwater and spray on a boat?

It carries an IP21 rating for solid objects and vertical dripping, not immersion or hose-down. Keep it under cover on a console or in a compartment, secured away from bilge water and direct spray, cap unused connectors, and wipe salt residue after a saltwater trip. It runs without exhaust, but it is not a sealed marine-rated unit.

How does it recharge between fishing trips, and from what sources?

Wall AC fast charge takes about one hour; a 12 V/24 V vehicle outlet takes about 3–4 hours; solar up to 120 W takes about 2.5–3 hours in good sun; and 100 W USB-C PD takes about three hours. Sunlight and mains feed can combine during a refill, and no solar panel ships inside the package.

Can it charge a phone, camera, and action cam while the electronics run?

Yes. The two USB-C ports, two USB-A ports, and top wireless pad handle phones and camera batteries while sonar and chart gear run off the DC bank or AC outlet. Light charging draws little current, but add the charging watts to the shared load and keep the total within the station's AC and DC limits.

Why is a pure sine wave inverter better for marine electronics?

A pure sine wave 110 V feed matches grid power quality and treats sensitive sonar, chartplotter, and charging circuits more gently than a choppy modified sine wave signal, helping avoid glitches or waveform stress. The T300 Pro delivers pure sine wave output alongside its mixed USB and DC connections.

Where does the $339.00 marine accessory station fit for anglers and boaters?

It fits small-boat anglers and day boaters who want a second, portable reserve for sonar, mapping, nav light, phone, and camera gear, kept off the engine starting battery and refillable from wall, vehicle, solar, or USB-C. It is not a propulsion or continuous heavy-pump solution; those call for a dedicated deep-cycle marine setup.

Conclusion

For an angler or day boater, the Gsike TELLUS-T300 Pro turns a 297 Wh compact pack into a portable second source for the electronics that keep a trip on course: sonar and chart running through the outing, phone and camera topped along the way, a small fan or light for comfort, and a clean sine-wave feed that treats sensitive gear gently. Its 11.1 lb carry body, mixed DC and AC outputs, four refill routes, and handle LED bar are built around the small-boat accessory load rather than fixed vessel installation.

The boundaries are equally clear: this station keeps electronics and small accessories alive and protects the engine starting battery, but it does not drive a trolling motor, windlass, or continuous heavy pump, and it must be kept dry, ventilated, and secured in sheltered spots on board. Within that accessory scope, it removes the risk of draining the starting battery just to keep navigation and communication gear working.

The Bottom Line for Fishing and Boating: anglers and small-boat boaters who need a portable 12V reserve for sonar, chart, nav light, phone, and camera gear will find the Gsike TELLUS-T300 Pro a quiet, carry-anywhere accessory plant that stays off the engine battery, while propulsion and high-demand pumps remain a dedicated deep-cycle job.

Article Keywords: 12V marine power plant for fishing and boating, fish finder battery backup station, portable power station for boat electronics, 297Wh fishing power plant, 300W portable power plant, Gsike TELLUS-T300 Pro, power plant portable, portable power station, 12V DC boat accessory power, LiFePO4 small portable power plant, portable station with LED light bar, Gsike power plant portable