Evening and outage sizing, Finland

Sizing a 5.12kWh Gsike Wall Battery for Evening Backup and Outage Self-Consumption

A sizing walkthrough for Finnish households: how to list evening and essential loads, convert the 5.12kWh cell rating into usable alternating current, estimate autonomy hours, and decide whether one Gsike wall pack or a parallel bank matches the property.

Sizing a home battery starts from your own consumption rather than from the enclosure on the shop page. For a Finnish home the two sizing questions usually arrive together: how much of the evening household load the storage can shift out of the imported kilowatt-hours, and how long a chosen set of essential circuits can keep running when the public supply drops. This guide applies both questions to the Gsike FixWall 5.0, a 51.2V, 100Ah, 5.12kWh wall pack, and shows the arithmetic between the cell rating, the depth limit, the inverter and the real load.

The pack stores direct current only and has no alternating-current outlet, no Wi-Fi or Bluetooth app. Its energy reaches the household circuits through a separate compatible 48V hybrid inverter that supplies the 230V installation. Sizing therefore has two halves: the battery bank on the 51.2V bus, and the inverter that feeds the essential and preferred circuits. The figures below plan around the Gsike unit as recorded; your installer sets the final battery capacity, cable rating, fuses and backup transfer for the measured property.

No Finnish tariff rate, feed-in payment or standing charge is assumed on this page. The value of shifting solar to the evening depends on your own supply contract and hourly pricing, which should be read from your bills rather than from a national average. The sizing method itself, however, is independent of those prices: it records what the house actually takes, separates evening and essential loads, and matches the reserve to that list.

Starting points for the evening backup calculation

  1. Cell rating: 51.2V nominal, 100Ah, 5120Wh equal to 5.12kWh, 16S1P LiFePO4.
  2. Continuous release: 50A charge and discharge, equal to 2560W for steady running; 100A, equal to 5120W, is a brief peak only and is not sustained.
  3. Depth of discharge: the cycle rating assumes 80% depth at 25°C; planning should hold a cautious reserve rather than draining to the cut-off.
  4. Voltage limits: 43.2V to 58.4V working range, 58.4V bulk and absorption charge.
  5. Communication: RS232, dual RS485 and CAN-BUS to the paired hybrid inverter, which reports state of charge and applies limits.
  6. Cycle horizon: 6000 cycles at 80% DoD and 25°C, roughly a ten-year design life, three-year warranty.
  7. Parallel expansion: up to sixteen matching packs on the 51.2V bus, 81.92kWh combined; no series, no brand or capacity mixing.
  8. Physical fit: 44kg, 640 by 428 by 160 millimetres, steel bracket and expansion bolts, IP54 indoor or sheltered use.
  9. Climate limits: operation minus 10°C to 50°C, storage 0°C to 35°C, no internal heater, charging below 0°C locked out.
  10. System boundary: battery-only DC node; the inverter, fuses, disconnects and cabling are designed separately by the installer.
Wall-mounted 100Ah Gsike pack in a Finnish utility room beside the hybrid inverter and load worksheet

A sizing worksheet separates the evening preferred load from the essential outage load before any capacity number is chosen.

How evening self-consumption and backup work

On a normal grid-connected day the hybrid inverter draws from the PV array, the battery and the public supply in the order configured for the system. Midday solar first covers whatever the house uses directly; any surplus charges the pack. Through the short Finnish afternoon and dark evening, when the panels produce little, the inverter draws stored energy for the chosen circuits before importing again. The battery's evening contribution is the share of that evening load it covers, which depends on both the stored reserve and how heavily the household runs after dark.

During an outage the inverter transfers the essential circuits onto battery supply automatically, provided those circuits were wired to the backup side and the inverter is set for transfer. The pack then feeds only the protected list; non-essential loads stay off. This separation matters for sizing: a household that only backs up lighting, the refrigerator and the router can expect many hours from a modest reserve, while one that tries to carry heating, cooking or heavy workshop tools on the same reserve drains the bank quickly and may exceed the continuous current rating.

The two goals pull the capacity in slightly different directions. Self-consumption storage is judged over daily cycles: how many kilowatt-hours of evening import it replaces, most clearly on sunny days. Outage backup is judged over event duration: how many hours the essential list survives, regardless of weather. A single 5.12kWh pack suits a light evening profile and a short essential-load outage; a household with either a heavy evening load or longer outage expectations should plan a parallel bank or discuss a larger installation with the installer rather than forcing this pack to cover more than its rating allows.

What energy actually remains for the evening

The 5.12kWh printed on the pack is the cell figure before any planning limit or conversion loss. Three planning steps move that number toward what reaches the circuits: the recommended depth of discharge, the inverter efficiency, and any margin kept for cold weather or battery age. The table below shows the standard planning corridor for one unit; the installed system may differ with the inverter model, cable condition and room temperature.

Planning stage Calculation Energy per cycle Use in sizing
Cell capacity Nominal 5.12kWh 5.12kWh Baseline label figure, not available household energy
Reserve at 80% DoD 5.12kWh × 0.80 ≈ 4.096kWh Depth kept within the rated cycle duty
Usable AC through ~95% inverter 4.096kWh × 0.95 ≈ 3.891kWh Planning basis for evening load and autonomy hours

Use the 3.891kWh figure as the planning basis rather than the 5.12kWh label. Round-trip efficiency, the inverter's real efficiency class, the length and gauge of the DC cabling, and the room temperature all shift the result up or down. In a cold but still above-zero room the cells deliver a little less freely, which is another reason to keep a margin on the essential list instead of designing to the absolute end of the reserve.

If a second identical pack joins in parallel, stored energy roughly doubles and the usable AC planning figure rises with it, up to the sixteen-pack parallel limit. The inverter rating, DC fuses and main cable must be matched to the larger bank at the design stage; adding a second unit later is mechanically permitted, but the battery channel and current rating of the existing inverter should be checked first.

Notebook listing evening loads and essential backup circuits for a Finnish household

Listing each load's steady wattage and startup current prevents the reserve from being sized on the evening kitchen total alone.

Load scenarios: apartment, detached house, weekend cottage, light workshop

City apartment in Helsinki or Espoo

A flat usually carries a light evening list: kitchen outlets, living room lighting, refrigerator, router and a few devices. Essential backup during an outage is limited to the circuits marked for the backup side. One 5.12kWh pack often matches this profile, provided the shared block allows wall fixing and the installer checks common-building rules before drilling.

Detached family house

A detached house with its own rooftop array tends to run a fuller evening load: lighting, kitchen appliances, laundry, hot-water circulation and electronics. Sizing compares the measured evening kilowatt-hours against the usable reserve; if the evening load regularly exceeds the pack's usable energy, a parallel second unit is the natural next step rather than deeper discharge of one pack.

Insulated lakeside cottage (mökki)

A cottage used through warmer months, or an insulated room kept above freezing, can size the pack around visit evenings and short outages on the lake route. The unheated wintered-over cottage is not a charging location: the unit has no heater and cannot charge below 0°C, so any year-round installation needs a heated dry room and the installer's temperature check.

Light workshop or small premises

A workshop or small shop with daytime stock, lighting and network gear may size the reserve around keeping essential equipment through a short interruption. Commercial load lists are built with the owner and installer, and the continuous 2560W rating must cover the steady load; heavy motors or heating elements are checked separately for startup and running current.

Across these scenarios the same rule applies: size to the written load list, not to the square footage of the property. Two detached houses of similar size can sit at very different evening loads depending on insulation, cooking method, heating equipment and how often the household is home after dark. Your own bills and a measured circuit list are stronger evidence than any average household figure.

What strengthens evening backup

  1. A measured surplus from the array: midday generation above daytime consumption gives the pack a real charge source on sunny days, instead of importing to fill it.
  2. A concentrated essential list: few, clearly marked backup circuits keep autonomy realistic; each added circuit extends the outage runtime demand.
  3. An evening-weighted household: families active after dark turn stored solar into evening use, which is where the self-consumption benefit appears.
  4. Repeated daily cycling: consistent charge and discharge through the week keeps the bank active and spreads its cycle life over useful shifted energy.
  5. A matched inverter: the 230V hybrid inverter handles transfer, charge profile and protocol, so the battery's reserve is actually accessible.
  6. A stable heated room: an indoor dry room above zero in winter keeps the battery within its climate envelope across the charging season.

What weakens evening backup expectations

  1. A load list grown by habit: unmarked outlets and shared circuits mean the backup list quietly grows past the reserve planned for it.
  2. Heavy heating or cooking on battery: large resistive loads draw well above the continuous rating and shorten runtime fast; these belong to a separate load calculation.
  3. Weak winter solar: dark-season weeks with little generation leave the pack relying on grid charging, so self-consumption savings shrink even where backup remains.
  4. Deep discharge to the cut-off: draining to the 43.2V limit shortens cycle life and leaves no margin for cold days or aging cells.
  5. Inverter idle and conversion losses: standby consumption and efficiency losses sit on top of the cell reserve and should not be ignored in the runtime estimate.
  6. A cold or damp placement: a room near freezing restricts charging, and condensation ages the housing; the pack has no heating element to compensate.

Autonomy calculation examples in hours

The table below divides the planning reserve of about 3.891kWh (3891Wh) by a few steady essential-load totals. These are planning examples for the essential circuits only; they exclude startup surges, inverter standby losses and any load added after the list was fixed. Real runtime is confirmed by the installer's measured load calculation, and the continuous 2560W battery rating must also be respected alongside the inverter's output rating.

Steady essential load Calculation from 3891Wh Approximate runtime Typical protected circuits
200W 3891Wh ÷ 200W ≈ 19.5 hours Lighting, router, a few electronics
400W 3891Wh ÷ 400W ≈ 9.7 hours Lighting, fridge, router and modest outlets
600W 3891Wh ÷ 600W ≈ 6.5 hours Fridge, lighting, network and small kitchen loads
800W 3891Wh ÷ 800W ≈ 4.9 hours A broader evening essential list, heavier margin required

Startup currents matter even when the steady wattage looks modest. A refrigerator, circulation pump or compressor draws a higher current for a brief moment at switch-on; the inverter and the battery's short-time peak must cover that moment, and repeated cycling of such loads shortens the average runtime. Record each essential device's rated wattage and check its startup requirement before treating the steady total as the whole picture.

For outage planning through a multi-day event, one 5.12kWh wall pack should not be assumed to keep a full home running. Its role is the essential-load level for shorter interruptions and the evening reserve for daily self-consumption. Longer autonomy, whole-house coverage or heavy pump and heating loads require a bank sized by the installer, with the appropriate inverter and protection layout; this page does not claim whole-home multi-day backup from a single unit.

Evening room lit from stored battery energy with the Gsike pack mounted in the adjoining dry utility space

Runtime estimates are most useful when the protected list is fixed first and the reserve is checked against both steady wattage and startup current.

Checklist before calculating your own evening backup

  1. Gather the bills: collect monthly imported and exported kilowatt-hours and any hourly or time-of-use detail from the supply contract.
  2. Map the evening load: note which circuits run after dark, their steady wattage and the devices that switch on together in the evening.
  3. Separate essential circuits: mark the backup list, record rated wattage and startup current for each device, and keep non-essential loads off that side.
  4. Read the array surplus: compare daytime PV generation with daytime household use to see how much energy is genuinely available to store.
  5. Check the inverter: confirm the 230V hybrid inverter's battery channel, protocol, charge profile and automatic backup transfer before sizing the bank.
  6. Measure the room: verify wall strength, clearance, ventilation, humidity and the winter minimum temperature of the proposed mounting space.
  7. Ask for a system quote: collect inverter, fuses, cabling, bracket extras and labour alongside the pack price, and let the installer confirm the final capacity and parallel count.

How the dark season changes the sizing view

Finland's short winter days mean the array produces little for stretches of January and February, so the battery often recharges from the grid rather than from surplus solar. In those weeks the self-consumption benefit narrows even though the backup role remains. A sizing calculation should not rely on summer generation alone: look at the cloudy and dark-season weeks in your consumption records, and decide whether the reserve is being bought mainly for summer evening shifting or for year-round outage protection, because the two expectations do not balance in the same months.

Cold conditions put a small additional margin on the usable reserve. The pack operates down to minus 10°C, but charging below 0°C is locked out and there is no heating element, so the chosen room matters as much as the capacity figure. A room that stays just above zero still delivers somewhat less freely than a warm plant room, which is another reason to plan the essential list with margin rather than draining the bank to its cut-off on every outage.

Compare your heaviest evening load against your lightest one, and size to the demanding season rather than the sunny July evening. A household that runs lighting, kitchen equipment and electronics after dark through the winter should use those winter evenings as the planning baseline; a cottage occupied only in warmer months can plan around visit-season use. The installer can convert the measured load list and the available inverter rating into a bank recommendation for whichever season the property actually uses.

Frequently asked questions about sizing the 100Ah unit for evening backup

How much usable energy does the 100Ah pack deliver per cycle?

On a 51.2V bus with 100Ah capacity the cell rating is 5120Wh, or 5.12kWh. At an 80% depth of discharge the planning reserve is about 4.096kWh, and through a roughly 95% efficient inverter close to 3.891kWh of alternating current reaches the circuits. Treat that usable figure as the sizing basis; the real number moves with the inverter, cabling and room temperature.

How do I build the essential-load list for a Finnish outage?

Walk through the circuits you must keep running: lighting, refrigerator, router, selected outlets and any water or circulation equipment. Record each device's steady wattage and its startup current, mark the circuits on the installation, and leave non-essential heating, cooking and workshop loads off the backup side. The installer wires that list to the protected inverter output.

How many hours of autonomy does one pack provide for a light evening load?

Using the 3.891kWh usable planning figure, a steady 200W essential load corresponds to roughly 19.5 hours, 400W to about 9.7 hours, 600W to about 6.5 hours and 800W to about 4.9 hours. These are planning examples only; startup surges, inverter standby losses and added circuits shorten real runtime.

Should I size the pack for evening self-consumption or for outage backup first?

Decide which goal dominates for your property. If the array produces a real daily surplus and the household is active after dark, evening self-consumption usually leads the sizing. If the main concern is short outage resilience for a small essential list, size to the autonomy hours and protected circuits first. A household with both goals at a high level should plan a parallel bank with the installer.

Which loads should stay on the essential circuits during an outage?

Typical essential loads are lighting, the refrigerator, network router and selected small electronics, plus any water-management or circulation equipment that the installer confirms can be covered. Large heating elements, electric cooktops and high-power workshop tools are not assumed onto this level; their startup and running current require a separate load and power calculation.

What reduces usable energy between the 5.12kWh label and the household socket?

Three steps apply: the 80% depth-of-discharge reserve, inverter conversion efficiency around 95%, and any margin kept for cold conditions and battery age. Cable condition, standby consumption and room temperature add further variation. The label kWh is the cell figure, not the energy delivered at the outlet.

Can a single 5.12kWh pack back up the whole house through a long outage?

No. This wall unit belongs to the essential-load level: it protects a selected circuit list for shorter interruptions and supports daily evening self-consumption. Whole-house or multi-day autonomy requires a larger bank, appropriate inverter rating and protection layout designed by the installer, and it is not promised by one 5.12kWh pack.

How do I decide whether a parallel second pack is needed?

Compare the measured evening kilowatt-hours and essential runtime against the usable reserve of one pack. If the evening load regularly exceeds the reserve, or outage expectations outgrow the listed runtime, a second identical pack in parallel is the supported route; series wiring is not allowed, and mixed brands or capacities must not enter the bank. The inverter's battery channel and current rating must be checked for the larger bank.

Does a refrigerator or circulation pump startup current affect sizing?

Yes. Compressors and pumps draw a higher momentary current when they switch on, even where their steady wattage is modest. The battery's 100A short-time peak and the inverter's surge rating must cover that moment, and frequent cycling of such loads reduces average runtime. Record startup requirements alongside steady wattage in the load list.

What records do I need before asking the installer for a size recommendation?

Bring your monthly imported and exported kilowatt-hours, the evening circuit list with wattages and startup currents, any hourly tariff information, the existing inverter model and protocol, and the dimensions and winter temperature of the proposed mounting room. With that material the installer can match bank size, parallel count and inverter rating to the property instead of relying on a generic capacity label.

Conclusion: work out your evening reserve first, then settle the bank size

Sizing the Gsike 5.12kWh wall pack for a Finnish home comes down to a written load list, a usable-energy basis around 3.891kWh per cycle and an honest separation between evening self-consumption and short outage backup. One unit matches a light apartment or cottage profile and a concentrated essential list; heavier evening demand or longer outage runtime points to a parallel bank planned with the installer.

Before choosing capacity, gather the bills, map the circuits, check the inverter protocol and transfer behaviour, and confirm the mounting room stays above freezing and ventilated. The numbers on this page are a planning corridor; the final bank size, protection devices and wiring are set by a qualified installer against your measured property.

Each FixWall 5.0 100Ah pack carries the smart BMS, the three communication links, the wall bracket and terminal set, and three years of warranty cover, priced at €849.99 against the €1,250.00 reference in the listing. Delivery to the listed EU countries is free, with 1 to 3 days of handling, 2 to 7 days in transit, and a 30-day return option.

Check the Gsike FixWall 5.0 product page for the complete spec sheet and current euro price.

Bottom line on sizing: list the evening and essential loads in watts, convert the 5.12kWh label to about 3.891kWh usable AC at the planning level, and let your measured consumption decide whether one Gsike pack or a parallel bank fits; reserve whole-home and multi-day expectations for a larger system designed by the installer.

Article Keywords: how much self-consumption does a 5kWh battery add to a Finnish rooftop PV system, what storage capacity does a typical Finnish detached house or apartment need after PV retrofit, 5kWh essential-load autonomy during a Finnish grid outage, evening kWh sizing for a dark Finnish winter day, usable energy after 80% DoD and inverter losses, fridge lighting router backup load list Finland, 51.2V 100Ah pack sizing against evening household consumption, parallel bank sizing for a larger Finnish household, Gsike FixWall 5.0 5.12kWh capacity planning, lead-acid replacement capacity check for a Finnish PV system, inrush current and startup load check for essential circuits, battery sizing worksheet for Helsinki Espoo Tampere Turku homes